pg_rewind — synchronize a PostgreSQL data directory with another data directory that was forked from it
pg_rewind
[option
...] { -D
| --target-pgdata
} directory
{ --source-pgdata=
| directory
--source-server=
} connstr
pg_rewind is a tool for synchronizing a PostgreSQL cluster with another copy of the same cluster, after the clusters' timelines have diverged. A typical scenario is to bring an old master server back online after failover as a standby that follows the new master.
The result is equivalent to replacing the target data directory with the source one. Only changed blocks from relation files are copied; all other files are copied in full, including configuration files. The advantage of pg_rewind over taking a new base backup, or tools like rsync, is that pg_rewind does not require reading through unchanged blocks in the cluster. This makes it a lot faster when the database is large and only a small fraction of blocks differ between the clusters.
pg_rewind examines the timeline histories of the source
and target clusters to determine the point where they diverged, and
expects to find WAL in the target cluster's pg_wal
directory
reaching all the way back to the point of divergence. The point of divergence
can be found either on the target timeline, the source timeline, or their common
ancestor. In the typical failover scenario where the target cluster was
shut down soon after the divergence, this is not a problem, but if the
target cluster ran for a long time after the divergence, the old WAL
files might no longer be present. In that case, they can be manually
copied from the WAL archive to the pg_wal
directory, or
fetched on startup by configuring recovery.conf
. The use of
pg_rewind is not limited to failover, e.g. a standby
server can be promoted, run some write transactions, and then rewinded
to become a standby again.
When the target server is started for the first time after running
pg_rewind, it will go into recovery mode and replay all
WAL generated in the source server after the point of divergence.
If some of the WAL was no longer available in the source server when
pg_rewind was run, and therefore could not be copied by the
pg_rewind session, it must be made available when the
target server is started. This can be done by creating a
recovery.conf
file in the target data directory with a
suitable restore_command
.
pg_rewind requires that the target server either has
the wal_log_hints option enabled
in postgresql.conf
or data checksums enabled when
the cluster was initialized with initdb. Neither of these
are currently on by default. full_page_writes
must also be set to on
, but is enabled by default.
pg_rewind accepts the following command-line arguments:
-D directory
--target-pgdata=directory
This option specifies the target data directory that is synchronized with the source. The target server must be shut down cleanly before running pg_rewind
--source-pgdata=directory
Specifies the file system path to the data directory of the source server to synchronize the target with. This option requires the source server to be cleanly shut down.
--source-server=connstr
Specifies a libpq connection string to connect to the source PostgreSQL server to synchronize the target with. The connection must be a normal (non-replication) connection with superuser access. This option requires the source server to be running and not in recovery mode.
-n
--dry-run
Do everything except actually modifying the target directory.
-P
--progress
Enables progress reporting. Turning this on will deliver an approximate progress report while copying data from the source cluster.
--debug
Print verbose debugging output that is mostly useful for developers debugging pg_rewind.
-V
--version
Display version information, then exit.
-?
--help
Show help, then exit.
When --source-server
option is used,
pg_rewind also uses the environment variables
supported by libpq (see Section 33.14).
The basic idea is to copy all file system-level changes from the source cluster to the target cluster:
Scan the WAL log of the target cluster, starting from the last checkpoint before the point where the source cluster's timeline history forked off from the target cluster. For each WAL record, record each data block that was touched. This yields a list of all the data blocks that were changed in the target cluster, after the source cluster forked off.
Copy all those changed blocks from the source cluster to
the target cluster, either using direct file system access
(--source-pgdata
) or SQL (--source-server
).
Copy all other files such as pg_xact
and
configuration files from the source cluster to the target cluster
(everything except the relation files).
Apply the WAL from the source cluster, starting from the checkpoint created at failover. (Strictly speaking, pg_rewind doesn't apply the WAL, it just creates a backup label file that makes PostgreSQL start by replaying all WAL from that checkpoint forward.)